Baumer NE215 Uživatelský manuál

Contents Page1 Safety indications 22 Getting to know the counter 42.1 Block diagram 53 Counter connection 63.1 Supply voltage connection 63.2 Assignme

10NE215Counter connecting and operating3.6 Executing the test routineThe test routine is described below.To start testPress the 2 and Druck key simult

11NE215Operating mode4 Operating modeThe operation and use of the counter are described in this section.● As soon as the power supply has been switche

12NE215If other values are changed, the value at witch the operating levelwas left can be re-displayed with the key after theprogramming mode has be

13NE215Operating modeSecondary counter preset statusTo readPress the key.Read the secondary preset value.To changePress the key● LED B1 flashes.Pr

14NE215Programming mode5 Programming modeThis section describes the procedure for programming the counter.Programming modeOperating parameters are set

15NE215Programming modeKey for printing DruckFunction in the operating modeThe simultaneous operation of the Key for printing an the 2 keystarts the t

16NE215Programming segment 1Information on the displays and changing individual values is alsogiven in Part 4.Press the key again.● The operating pa

17NE215Programming modeProgramming segment 2In the second programming segment, the message STAT appears inthe display, signifying status selection.●

18NE215Programming segment 3Programming segment 3 begins with programming line 21.14 programming lines are displayed in sequence in these segments.Def

19NE215Programming modeLine 36Secondary counter functions XB0 * External1Internal2TachometerLine 37Pulses per unit of measurement, as tachometer1

2NE215General Information/Safety InstructionsGeneral InformationIn the following you will find the explanations of the symbols usedin this operating m

20NE215Programming field 4Line 43Baud rate0 * 4800 baud1 2400 baud2 1200 baud3 600 baudLine 44Parity0 * Even parity1 Odd parity2 No parityLine 45A

21NE215Programming mode5.2 Counting modes for the main and totalizing counterUp/down counting with two counting signals, phase-offset by90 degreesThe

22NE2156 Technical dataDisplay 7-segment-LED display8-digit, redwith minus signDigit height 7,6 mmPower supply As per purchase orderPower consumption

23NE215Technical data6.1 Dimensions and cutout size6.2 Default settingsThe following parameters are programmed into the counter by thefactory prior to

24NE215Open interface description7 Open interface description7.1 General informationThe open interface is of the RS485 type. It is possible to send th

25NE215Open interface descriptionImportantThe blanks between the particular characters of the commandsonly serve the purpose of better legibility. The

26NE215Open interface descriptionThe protocol: <STX> Address line P [VZ] data <ETX> [<CR>]can be used for each line. The answer of t

27NE215Open interface description7.5.2 Switch counter to PGM mode or RUN modeThis command allows you to switch the counter upon every callbetween the

28NE2157.6 Output to the printerThe command parameter „D“ allows the initiation of the output ofthe lines 01, 02, 03 and 05 to the printer.7.6.1 Appea

29NE215Open interface descriptionAnswer: <STX>3501D<CAN>4<ETX><CR>7.6.4 Printout of the lines 02, 03: preselections P1 and P2A

3NE215Safety InstructionsThe overvoltages to which the units are subjected at the connectionterminals must be limited to the value of the overvoltage

30NE215General structure of the error messages:<STX> Address Line Status <CAN> Error number <ETX> <CR>Example: Address=35, Lin

31NE2157.9 Operating PlanLine Display Short description01 Preselection counter XP02 Preselection 103 Preselection 2Not applicable05 Totalizer06 Batch

32NE2157.10 Programming planLines in italic* = Factory settingLine 11-18 Status for line 11-180 * Parameter can be changed1 Clearing and/or input dis

33NE215Line 36 Function of batch counter0 * external1 internal2 TachometerLine 37 Impulses per unit at tachometer00.00 Minimum value1.00 * D

34NE215Supplement8. Supplementary operation manual foropen and closed interface(February 1994, Erg. 31.8.1994)The addendum describes the interfaces an

35NE215- the number of stop bitThe contacts 21(-T,R) and 22(+T,R) are assigned to the open RS485-typeinterface.9. Supplement to the scaling factor man

36NE2159.2 Modifications in Chapter 3: „Counter connection“New pin assignment for pin 15: scaling on.9.2.1Modifications in Chapter 3.3: „Assignment of

37NE215Suitable encoder PTB-version10. Suitable encoderTechnical DataModel Incremental EncoderRPM value 10.000 min-1Supply Voltage 10...30 VDC, with r

38NE215Track ATrack BZero pulseSuitable encoder PTB-versionPin assignmentAssignment Cable colorA blueB beige0 greenUB brown0V blackOutput signalsSigna

39Models/order designationPart numberNE215. 1 AX0 Display 5 In cm, 9999.9950 pulses/rev.w/o interface/RS232

4NE215Getting to know the counter2 Getting to know the counterThe counter comprises the following:– Presetting the counter with 2 preset value, (prel

5NE215Example for printMain counter systems: (PTB-approved)1 up/down preset counter with totalizer.Batch counter systems: 1 preset counter, adding.A k

6NE215Counter connectGNDRxDTxDRS23226 25 24 2322 21RS485T, R +T, R -1 Relay contact output P11 Relay contact output B11 Relay contact output P23 Count

7NE215Counter connect3.1 Connecting the power supplyFor power supply following voltage ranges are available:AC 115/230 VAC (50/60 Hz)DC 24 VDC ±10%Vo

8NE2153.3 Assignment the signal inputsTerminals 12 to 17 are AC optocoupler inputs. Terminals 12 (track A)and 13 (track B) are pulse inputs for the ma

9NE2153.4 Connecting the encoder supplyConnect the encoder supply at terminals 19 and 20.Do not use the encoder supply to supply non-earthed inductive